APP switch ON button does not turn lights to full?
The ‘pseudo switch’ on the ‘Switch’ page of the APP is only for illustration, the ‘ON/OFF’ button on the APP acts different from the physical button on the switch. The ‘ON/OFF’ button: • ‘ON’ button on the switch sends ID to the sensors, sensor translates it to ‘FULL ON/OFF’ commands. • ‘ON’ button on the APP ‘AUTO/OFF’ commands sensors. It does not send exact ‘button and switch ID’ to sensors.
Can EFS106 sensors designed for daylight harvesting be used for dusk to dawn operation?
Sensors with daylight harvesting can turn off fixtures, when the driver on the fixture will cut off the LED current when 0-10v signal drop down to range of 1%-10%. Most of outdoor fixture drivers will cut off LED current at 5% to 7% dimming level. Following are the detailed step-by-step description of the configuration to allow EFS106-DLH sensor to turn on off fixture by daylight harvesting sensors.
1. Prepare: please have a RP0 and powered it on with a proper power bank. a) Some power banks may cut off power to RP0 because the current is very small, please make sure to the power bank you use can sustain the continue power supply.
2. Set the RP0 to factory setting before commission (press and hold the reset button on RP0 to reset it when necessary) and keep it powered on with you.
3. Create a new zone on you APP, and name it properly.
4. Commission all EFS106-DLH sensors to the zone.
a) Factory setting RP0 can help commission the sensors.
b) You may need to
5. Commission the RP0 to the zone, and keep it powered on and with you after commissioned it.
a) You need to commission the RP0 from “More”, “Device Info” page on the APP. Factory setting RP0 will show up in ‘Add lights’ page but you won’t be able to commission it from here.
6. Go to ‘Group’ page, click the dimming button on ‘All Lights’ group, click the sensor setting button to bring out the sensor setting page.
7. Enable ‘Daylight harvesting’, enable ‘Motion’ sensor, set proper T1 (say 20 minutes), set T2 to ‘INFINITE’, set proper Dim evel (say 20%). Then click ‘Save’.
a) You will see fixture flush to indicate it received the command.
8. During the night, go to ‘Group’ page, click the dimming button on ‘All Lights’ group, dim all lights to 100% and click ‘A’ to save the auto point.
9. Dim All Lights to 100%.
10. Go to ‘More’ page, click ‘Trim Settings’, select “Groups”, click the ‘’ beside ‘ALL Lights’,
a) Click ‘Low-End Trim’, select ‘1%’, then click ‘Send’ in ‘Low-End Trim’ section.
i. All sensor should dim to 1%, in this case, fixture should be turned off, otherwise, this won’t work.
11. Dim All Lights to 100%. 12. Go to ‘More’ page, click ‘Trim Settings’, select “Groups”, click the ‘’ beside ‘ALL Lights’,
a) Click ‘Daylight min dim’, select ‘1%’, then click ‘Send’ in ‘Daylight min dim’ section.
i. All sensor should dim to 1%, in this case, fixture should be turned off, otherwise, this won’t work. Starting from step 6 in the outdoor jobsite, you may need to walk around with RP0, and click “Save” for a few times to make sure all sensors received setting and commands.
Test to confirm:
1. Turn on all lights from APP, then cover the sensor to prevent daylight from coming to the sensor (or test it in the night), fixture should be turn on and dim to 100%.
2. Remove the cover, use a flashlight or other light to direct at the sensor, fixture should dim down and turn off.
3. Test in the night, the fixture should dim down to Dim Level after T1 timed out, and does not turn off. It dim up to 100% when motion is detected.
Can I control lights with computer or PC?
There is currently no native way to directly control Keilton devices from a desktop or laptop computer.
However, devices can be controlled indirectly using a BLE-485 gateway device connected to your computer.
How it works:
Connect the BLE-485 gateway to your computer via USB Pair the gateway with your Keilton product using Bluetooth Install a terminal program on your computer that can send serial commands Use text commands to turn lights on/off, dim, recall scenes This setup allows basic unilateral control of lights from a computer. But the mobile app is still required for configuration like creating groups or renaming devices.
Limitations:
No editing of project settings and structure from a computer Control is one-way only (computer to lights) Limited to basic textual serial commands
Can I share project setting control(QR Codes) to other users remotely?
You can easily grant other users remote access privileges to control your project. Here’s how:
In the Keilton app, locate the QR code associated with your project. This QR code contains all the information needed for others to connect to the project. Save a picture of this QR code to your phone’s photo album. Share this QR code picture with other users via email or text. When the remote user receives the QR code picture, they simply open the Keilton app on their own device and scan the QR code. Scanning the QR code will automatically give the user access to your project with the privilege level you specified when generating the code. That’s it! By sharing the QR code picture, you can securely give access to your project without needing to share your login credentials. The user just needs to scan the code you provide to gain access.
Can I use Keilton app to control other manufacturer's brands of Bluetooth lighting systems?
In most cases no, the Keilton app is designed exclusively for Keilton systems and would not typically be compatible with other brands of lighting hardware or software.
Can Keilton+autani Bluetooth switches such as IWS102(wall switch occupancy sensor) operate devices plugged into the WF20R controlled receptacle?
Yes, the IWS102 or any Keilton+autani Bluetooth switch can provide ON/OFF control to any device that is plugged into the controlled portion of the WF20R receptacle.
The steps to facilitate this are:
Commission the IWS102 to same Zone as the WF20R is on. Create a Group and add both IWS102 and WF20R to same Group. Enable motion sensing for either Occupancy or Vacancy mode.
Enable Linkage.
Set desired time-outs for T1/T2.
Set “hold time” equal to T1 When the ISW102 triggered, it will turn on the controlled receptacle of the WF20R and off after motion times out. User may also press the ON/OFF button on the IWS102 to turn on the receptacle.
How can I locate where the CS107x snesor is installed?
There are a few methods to help identify the physical location of an installed sensor:
Commission sensors individually:
If possible, power off all ceiling sensors, then power on and commission just one sensor at a time and add it to the zone. Name each sensor as it is added to make identification easier.
Connect a non-smart fixture to the CS107 relay output, and turn it on/off to locate CS107: Use the relay output on the sensor to directly control a standard, non-BT-enabled light. Test using these steps:
A. Create a group on the zone called G1. No member lights in this group. In the configuration page, bind the sensor to this G1 group. Set other parameters to proper values as required by the project (be sure to disable the photocell of G1)
B. Trigger sensor and observe response: Return to the Group page, click the on/off toggle button to turn on/off the G1 group, and identify the CS107 location. Note there will be an audible click to help identify the relay.
Bind the CS107 with another sensor/controller. Turn on/off to locate CS107
CS107 can turn on other Keilton sensors and controllers.
Test using these steps:
A. Create a group in the Zone called G1.
Add a sensor or controller to the group called L1.
Enable motion sensor function for group G1
B. In the CS107 configuration page, bind G1 to CS107. Set other parameters to proper values as required by the project (be sure to disable the photocell of G1)
C. Turn on G1. On the ‘More’ page, click ‘Motion Sensor Test’ (L1 should be turned off) Wait a few seconds, then try to trigger the CS107 to find out which device activates L1
Check Nearby Devices
Use the ‘Nearby Lights’ function in the app and walk below the sensor. Refresh nearby devices until the sensor appears with the strongest RSSI (negative number closest to 9). This indicates you are closest to the sensor’s physical location.
How can I tell which firmware is present in the connected hardware?
“When you click ‘More’ at the bottom of the screen, click ‘Nearby Lights’. On this page, on the top right of the screen you will find ‘Type Rev’
For each device ID, the numbers shown on the top row represent the firmware rev. (example 0x68-20). The numbers shown on the second row indicate the firmware date code (example: 221103 = November 3, 2022)
How can I tell which sensor or control node is closest to me?
When you click ‘More’ at the bottom of the screen, click ‘Nearby Lights’. On this page, on the top right of the screen you will find ‘ID RSSI’.
The device ID with the lowest number is typically the strongest signal and may be the closest device to the user.
How do I get the energy report file?
To collect energy consumption data and generate an energy report, you require a CR01 energy monitoring dongle. The CR01’s features are as follows:
It is powered by a USB-A receptacle.
It has an embedded Real time Clock (RTC) to synchronize time for all devices in the zone, including an internal battery to maintain time during power outages.
It records the energy consumption raw log onto a SD card.
For more detailed information, please consult the CR01 Specification. Keilton+Energy+Monitoring+Instruction.pdf
The CR01 records the energy consumption raw log for every device in the zone at 15-minute intervals. In a zone with 100 controllers, it will produce approximately 28 Megabytes of data per month.
How do I find a Bluetooth sensor when not connected directly to a luminaire?
Open the Motion Sensor Testing function on the More page.
Select “Start Testing”.
Open the Lights page.
Walk around under the sensors in question.
The lights icon will indicate “ON” when you are near the sensor.
This will identify the sensor and the associated icon in the app.
Then press and hold the icon till the “Light Dimming” page opens.
Rename the sensor. Suggest using naming to indicate location, i.e., room number or room name.
Open the Groups page.
Add the sensor to the group of lights you wish to control.
Select the “Light Bulb” icon in the group and then select the “Motion” setting button on lower right-hand corner and choose the settings for your group. Select “Save” when complete.
How do you get a light back online?
If a light/sensor is not connected in the Zone then you must reset the device by either pressing the reset button on the device (see product instructions) or perform a manual ON/OFF sequence operation. The steps are:
Confirm all lights are off.
Turn on lights for 8 seconds; then turn the power off for 10 seconds.
Immediately turn the lights on and off, then wait for another 10 seconds. Repeat 3 times.
Turn the lights on for 8 seconds, then turn the power off for another 10 seconds. Repeat 2 times.
Turn the lights back on. Blinking Lights indicate a successful factory reset. All previous settings and data for these lights have now been deleted. Waiting for at least 10 seconds will ensure that the fixture is completely powered off.
The duration will vary depending on the driver and the power supply. If the driver can cut power to the fixture within 3 seconds, then you may change the waiting period from 10 to 3 seconds to facilitate a faster reset time.
How many devices can be in one ZONE?
A maximum of 100 lights can be in a single ZONE.
How many phones can control the lights at the same time?
The maximum number of phones that can simultaneously control the lights is limited by the number of online devices in the project.
For example, if there are 10 lights actively online, then up to 10 phones can connect and control the lights at the same time. Each phone needs an individual online device to grant access.
Please note the app still occupies the Bluetooth connection even when running in the background. To allow a new phone to connect, completely force quit the app on the first phone to fully release the Bluetooth connection.
Important: Do not perform editing operations like adding, deleting, or modifying lights, scenes, or groups from more than one phone simultaneously. This can lead to data corruption. Only one phone should edit project details at a time.
How often is the Kielton app updated?
The Keilton app is typically updated approximately once per month.
These releases include:
*New features, functionality, and improvements
*Bug fixes and issue resolutions
*Performance enhancements
Though the cadence can vary, our aim is to push major app updates on a monthly basis. This allows us to continuously expand capabilities, while also addressing any problems or stability concerns promptly.
Users will be notified through the App Store/Play Store when new versions are available. We highly recommend keeping the app up-to-date to take advantage of the latest features and fixes.
Major updates will also be announced on our website and in other communications. Please reach out if you ever have any feedback on the app or suggestions for new capabilities!
If a site loses power, will any commissioning be lost when the power comes back up?
LiteTrace Keilton network system will not lose their settings if power is lost. They have non-volatile memory and retain their settings during power interruption.
If the user specifies a brightness level for calibration, how does that effect other strategies such as setting the Trim values (high end trim, daylight min dim, low end trim)?
The user-specified calibration brightness during sensor commissioning does not affect the configured high-end and low-end trim settings.
The high/low end trims set the absolute maximum and minimum light levels allowed. These establish preset boundaries. The calibration brightness is used to tune the daylight harvesting performance within those trim endpoints.
For example:
High End Trim = 80% (4000 lumens for a 5000 lumen fixture)
Low End Trim = 20% (1000 lumens for a 5000 lumen fixture)
Calibration Brightness = 50% (2500 lumens for a 5000 lumen fixture)
With these settings:
The calibration will tune the daylight dimming to maintain around 2500 lumens. The light level will never exceed the 4000 lumen high end trim nor drop below the 1000 lumen low end trim. So in summary, the trims create firm dimming limits, while the calibration tuning happens in between those. The trims remain unaffected.
This provides both guaranteed minimum/maximum light levels as well as tuned automatic daylight dimming based on conditions.
Is the app automatically updated?
Yes, the Keilton app will automatically update to the latest version once it is released. Users do not need to manually install updates.
When we publish a new version of the app, it will automatically be pushed and installed on your device provided:
*Your device is connected to the internet
*Automatic app updates are enabled in your device settings
*The Keilton app was downloaded from the official App Store/Play Store
Users will receive a notification from the app store when the Keilton app updates in the background. We recommend leaving automatic updates enabled to always have the latest features and fixes.
The auto-update capability means you can ensure you are always running the most up-to-date Keilton app version without any extra steps.
Is there a way using the App to push out a High-end trim to all lights on a project or do you have to do it individually light by light?
Yes, there is an option to set Trim levels for All Lights in the Zone (Network) under the Groups column. You would need to open each Zone while at the site and connected to the mesh network.
Light level and CCT for luminaires go to different level and CCT when lights turn off via a control function such as "OFF" by non-occupancy or power is interrupted.
Set the dimming level and CCT setting on the Lights setting page and select ‘A’ button on lower right corner to save the settings.
My light switches only work when my phone is within range of the switches. How can I setup the switches to work manually without my phone being in the area?
Switches need to be paired with the lights in the Keilton+autani app. Please see the Keilton+autani App Instructions. Keilton+App+Instruction.pdf Or the Setup Guide Keilton+Autani+Setup+Guide.pdf
Another reason for them not working outside of the app is the battery has not been installed or is dead. The battery is shipped in same package as switch but needs to be installed.
If you have further issues, contact Technical Support: https://autani.zendesk.com/hc/en-us/requests/newsupport@autani.com
Contact phone: 443-320-2233 (M-F 9am-5pm ET)
What are the differences of "Admin" and "User" privileges?
There are two main privilege levels on a Keilton project, associated with two distinct QR codes:
Admin Privileges:
*Orange QR code
*Automatically granted to the project creator
*Has full control over the project
*Can add, delete, rename groups, scenes, switches, schedules
*Can modify sensor settings and parameters
*Can perform any operation on the project
User Privileges:
*Green QR code
*Granted when project access is shared with others
*Has limited, read-only capabilities
*Can only dim or turn off lights
*Cannot modify or edit the project
In summary:
*Admins have full control and configuration access
*Users have read-only access to control lights
*Two levels allow granting basic access without full control
What are the Zone naming parameters?
When naming a Zone in the APP, only the following characters are allowed: lower case, capital letters, numbers, and following symbols ( . , – : _ + ).
What does the "A" inside the light logo mean?
The Keilton app shows a light bulb icon next to each light on the project. This represents the current status of that light.
If you see an “A” inside the light bulb icon, it means that the light is in automatic mode. Automatic mode means the light is being controlled by sensors, not manually.
Here’s what happens in automatic mode:
Sensors detect occupancy and ambient light levels and automatically turn the light on or off as needed.
Lights will automatically dim up or down depending on the sensor readings, without any user input.
The light is essentially controlled by the sensors, not manual inputs.
Once you manually control the light, such as turning it off or setting a scene, it will exit automatic mode and the “A” will disappear from the icon.
So in summary, the “A” indicates a light is currently being automatically controlled by sensors, not manual inputs. It lets you know that light is in automatic mode at a glance.
What is RSSI?
Received Signal Strength Indicator. RSSI is a measurement of the power level present in a received radio signal. RSSI is used to determine wireless signal strength and quality. It can help troubleshoot connectivity issues.
RSSI is measured in dBm (decibels relative to one milliwatt). Typical values range from -30 dBm (excellent signal) to -90 dBm (very weak signal). The higher the dBm value, the stronger the signal. -30 dBm is a much stronger signal than -90 dBm for example. RSSI measurements fluctuate rapidly, so values typically need to be averaged over time for accuracy. Factors like distance, obstacles, interference, weather, and network traffic can affect RSSI.
Thus, when an RSSI value is represented in a negative form (e.g. −100), the closer the value is to 0, the stronger the received signal has been.
In the Keilton system, when RSSI <= -60 dBm the signal is considered GOOD. When RSSI <= -80dbm the signal is considered ACCEPTABLE.
What is the difference between BLE, Bluetooth, and Bluetooth mesh? Is BLE the same as Bluetooth mesh?
No, Bluetooth Low Energy (BLE) and Bluetooth Mesh are not the same things. Here’s a breakdown of the differences between BLE, Bluetooth Classic, and Bluetooth Mesh:
1. Bluetooth Low Energy (BLE):
– BLE is a low-power wireless communication protocol designed for short-range communication.
– It operates in the 2.4 GHz ISM band, just like Bluetooth Classic.
– BLE is optimized for low power consumption, making it suitable for battery-powered devices like fitness trackers, smart home sensors, and other IoT devices.
– BLE supports point-to-point connections between two devices, but it does not inherently support mesh networking capabilities.
2. Bluetooth Classic:
– Bluetooth Classic is the original Bluetooth standard, designed for continuous data streaming and higher data rates (up to 3 Mbps).
– It consumes more power than BLE but offers higher throughput.
– Bluetooth Classic is used for applications like wireless headsets, file transfers, and device-to-device communication where higher data rates are required.
– Like BLE, Bluetooth Classic does not inherently support mesh networking capabilities.
3. Bluetooth Mesh:
– Bluetooth Mesh is a separate protocol built on top of Bluetooth Low Energy (BLE) technology.
– Buetoooth Mesh is the technology used in LiteTrace’s Keilton+autani products
– It adds mesh networking capabilities to BLE, allowing devices to communicate with each other in a mesh topology.
– In a Bluetooth Mesh network, devices can relay messages to each other, extending the range and reliability of the network.
– Bluetooth Mesh is designed for creating large-scale, multi-node networks for applications like smart home automation, industrial automation, and asset tracking.
– Bluetooth Mesh introduces additional features like message relaying, self-healing capabilities, and support for multiple simultaneous communication paths.
In summary, BLE and Bluetooth Mesh are not the same. BLE is a low-power communication protocol focused on point-to-point connections, while Bluetooth Mesh is a separate protocol that adds mesh networking capabilities on top of BLE, enabling many-to-many communication and large-scale mesh networks.
Bluetooth Classic is the original Bluetooth standard, designed for higher data rates and continuous data streaming, but it does not support mesh networking capabilities either.
What is your system's typical response time from when a button is clicked to sensor and light response?
The time from when the button is clicked to when the sensor starts responding is fast at 40 milliseconds (ms). After being triggered, the sensor does not immediately snap the lights on/off. Instead, it gently fades the lights up or down over 500ms. The 500ms fade time provides a smooth and gradual dimming transition, preventing harsh or abrupt light changes. Together, the very fast 40ms trigger response and 500ms fade time allow the system to react instantly to occupancy changes while still ensuring comfortable light dimming. These performance metrics indicate LiteTrace has engineered the system for quick response and optimal user experience.
What phone models are supported by the APP?
The Keilton app requires Bluetooth 4.1 hardware or later on your device in order to work properly. This is because the app uses BLE (Bluetooth Low Energy) to communicate with Keilton devices. Phones with Bluetooth hardware earlier than 4.1 will not work correctly.
Apple Devices:
The Keilton app is compatible with most iPhones and iPads using iOS 10 or higher. This covers most iPhone models from the iPhone 5 onwards.
Android Devices:
The app supports Android 5.0 (Lollipop) or newer. It should work on most modern Android smartphones but may have issues connecting on older models or devices with heavily modified versions of Android.
Troubleshooting Tips:
If having connectivity problems, first make sure your device supports Bluetooth 4.1 or later. This can be checked in your phone’s settings. Older Bluetooth hardware is the primary reason the app may fail to operate normally.
Outdated OS versions, custom ROMs, or changes made by device manufacturers can also cause compatibility issues on some Android devices.
What should I do if i lost my phone before I share QR code with others?
The Keilton app saves a QR code image in your photo album when you first create a new project. This code contains the details needed to connect to the project.
If you lose your phone before you have a chance to share the QR code with others, here are some tips:
Regularly back up your QR code images to a safe location like cloud storage or an external hard drive. This ensures you have a copy if your phone is lost. If you can replace the phone for the same account, the QR images should be restored to the new phone once the account is reactivated.
As long as you still have the QR code image file, you can install the Keilton app on a new phone and regain access by scanning the code.
If you completely lost the QR code before sharing it, you will, unfortunately, have to reset all your devices back to factory default settings. Go to FAQs – Litetrace for information on resetting devices. This will remove any existing programming and project configurations. You’ll have to set up your project from scratch again. Another option is to visit the site and open a new app and go to More tab and then open Nearby Lights. Record the Network ID’s shown under the Network name for the devices connected to “Network Unknown”. Then send an email with the information to customer-support@litetrace.com. An effort will be made to locate the QR codes. This requires considerable resources to complete.
To avoid losing access, be sure to back up your project QR codes periodically before sharing them. The codes act as your “key” to access your project if your phone is lost.
Where is the Keilton+Autani APP available?
The Keilton+autani App is available on the app store. Use these QR codes to download.
Why do I see devices continuously connecting/disconnecting/reconnecting in the app during commissioning?
It sounds like there are a couple main reasons users may see devices constantly connecting and disconnecting in the app during the commissioning process:
- If there are too many factory-default lights powered on close together, this can overwhelm the app with wireless RF signals as it tries to maintain connections with all the lights broadcasting setup signals simultaneously. The excessive number of lights flooding the network makes it difficult to hold steady connections.
- As the user physically moves around the jobsite during commissioning while holding their phone/tablet, they may walk in and out of range of different devices. This forces the app to lose and reestablish connections as it jumps between communicating with nearer and farther devices.
Additionally, the normal behavior of toggling between the “Lights” and “Added” pages in the app requires switching communication between already commissioned zones versus factory default lights. So, the constant shifting between these modes as part of regular commissioning also leads to a lot of reconnecting.
In summary, dense clusters of factory default lights and user movement during the process can cause a flurry of dropped and reestablished connections as the app tries to keep up. This is expected behavior but limiting the number of lights on at once and commissioning from a fixed location can help reduce the connection churn if it becomes problematic.
Why do lights show "Full-ON" on Light Status Page in APP when Trim Level is set for less than "Full-ON"?
The app light status is showing the commanded state, not the actual output. So even if the trim limits the output to 80%, if the user has set the dim level to 100%, the app will show 100% status.
Why do the Zones have a red dot next to the Zone name?
A red dot next to a zone name in the Keilton app can indicate two possible issues:
Low batteries – This means one or more devices in the zone has batteries below 20% and needs replacement. The red dot appears as a low battery warning.
Poor connectivity – The red dot can also appear when a zone has trouble syncing data due to poor project connectivity.
In this case:
*The red dot indicates the zone cannot connect to sync lighting data.
*This is usually caused by an intermittent network issue preventing proper data syncing.
*Once connectivity is restored and sync completes, the red dot will disappear.
Comments
0 comments
Please sign in to leave a comment.